FRP grating is a molded or pultruded composite panel for platforms, walkways, trench covers and stair treads where steel would corrode. It is lightweight, non-conductive and needs no painting, giving decades of service in chemical, marine and wastewater environments.
Greenlogy TEC supplies molded grating in square and rectangular mesh and pultruded grating in high-load profiles, with polyester, vinyl ester and phenolic resin systems. New to FRP? Start with the molded vs pultruded comparison and the specification guide, then send us your panel sizes for a quote.
More guides: load table | anti-slip grating and stair treads | FRP vs steel grating | all guides
Frequently Asked Questions
What is FRP grating?
FRP (fiberglass reinforced plastic) grating is a composite panel made from glass fibers and resin, molded or pultruded into an open mesh. It is used where steel grating would rust: platforms, walkways, trench covers and stair treads in chemical, marine, wastewater and food plants.
Molded vs pultruded FRP grating - which should I choose?
Molded grating has a square or rectangular mesh with equal strength in both directions, ideal for walkways and platforms. Pultruded grating carries load in one direction and gives higher stiffness for long spans and heavy loads such as vehicle traffic. Our comparison guide walks through both.
How do I choose mesh size and thickness?
Mesh size depends on the smallest object that must not fall through, typically 38x38 mm for foot traffic and 19x19 mm where small tools are used. Thickness (25, 30, 38 or 50 mm) follows from the load table for your span and load. Send us span, load and environment and we recommend a panel.
Is FRP grating slip resistant?
Yes. The grit surface provides a slip-resistant walking surface even when wet or oily, and is commonly used for stair treads, ramps and walkways. Anti-slip options are covered in our anti-slip guide.
Can FRP grating be cut on site?
Yes. Molded and pultruded panels are cut with a common circular saw or grinder with an abrasive or diamond blade, and cut edges are sealed with resin to close the fibers. We can also pre-cut and pre-drill panels to your drawing before shipping.
How do I get a quote?
Send your panel size, mesh, thickness, resin type, color and quantity through the contact page or by email, and we reply with price, lead time and shipping options. Custom colors, cut-to-size panels and stainless or FRP fasteners are available.
FRP grating from a supplier that makes both families
Greenlogy TEC manufactures molded and pultruded fiberglass reinforced plastic grating for walkways, platforms, trench covers and stair treads. Both families come from the same supplier, so a project that needs molded panels for the general deck and pultruded panels for the long spans does not have to be split between two suppliers.
Panels are supplied in the standard sizes listed on the specification page and cut to your layout. Openings, penetrations and edge infill can be cut on site with standard carbide tools, or we pre-cut and pre-drill the panels before they ship.
Which grating for which duty
Start from the service condition, then confirm the panel against the published load table.
| Service condition | Start with | Usual resin | Why |
|---|---|---|---|
| General walkways and platforms | 38*38H30 molded | OFR-25 / IFR-25 | 68% open area - drainage and snow shedding, standard duty |
| Small parts must not fall through | 19*19H30 molded | OFR-25 / IFR-25 | 40% open area, the tightest molded mesh |
| Vehicle traffic and long spans | I-4010 or HL-4020 pultruded | VEFR-25 | Load bars carry along the span; HL-4020 has the deepest bar |
| Closed walking surface | T-1210 / T-1215 pultruded | VEFR-25 | 12% open area for a near-solid top |
| Stair treads | 38*152H38 or 25*152H38 tread panel | OFR-25 | Rectangular mesh with the bearing bars running lengthwise |
| Severe acids, or fire and smoke limits | Molded or pultruded | VEFR-25 / MP-5 phenolic | Vinyl ester for chemical load, phenolic for low smoke and flame |
The molded versus pultruded comparison covers the trade-off in stiffness and direction of strength, and the load capacity guide carries the spanning data for each mesh and series.
What to send for a grating quotation
A quotation is only usable if it is matched to the installation. These six items are what lets us answer with a specification rather than a price per square metre:
- Span between supports, and whether the panel is fixed or removable
- Load - foot traffic, trolley, or wheel load with the contact area
- Environment - the chemicals, their concentration and the service temperature
- Mesh and height, if already specified, or the smallest object that must not fall through
- Panel sizes or a layout drawing, including openings and penetrations
- Quantity, delivery address and the date the panels are needed on site
Send that list to admin@greenlogy.cn or through the contact page. The reply quotes the matching mesh, series and resin system, with price, packing and delivery confirmed together.
Panel sizes, cutting and fasteners
Molded panels run up to 1220 x 4000 mm, with some meshes also available at 1524 x 4000 mm and 915 x 3050 mm. Pultruded panels are 1220 or 915 mm wide and 3050 or 6100 mm long. Cut edges are sealed with resin to close the fibers for the service environment, and panels can be delivered pre-cut and pre-fitted to your drawing.
Panels are fixed with 304 or 316 stainless steel or FRP duckbill clamps, so the fasteners outlast the deck in the same environment. Custom colors, cut-to-size panels and the full fastener range are quoted with the panels.
Specification guide: mesh, height, panel size and resin | load capacity | molded vs pultruded | anti-slip surfaces | FRP vs steel grating | reference library
简体中文
English