Molded FRP Grating: Mesh, Depth, Resin and Load
Mesh, depth, resin and span decide how much a grating carries and how long it lasts
Selection starts with four variables
Molded FRP grating is made by laying glass-fibre rovings into a grid in a mould and pouring resin over them in a single moulding step. Mesh, panel depth, resin system and support span together decide its load capacity, corrosion resistance and service life; colour and surface pattern are secondary.
An enquiry that says only "one piece of 38 molded grating" carries far too little information. At the same 38 mm mesh, a 25 mm panel and a 50 mm panel can differ by more than a factor of two in capacity; at the same 38 mm depth, orthophthalic and vinyl ester resins cover completely different chemical environments.
The sections below take the four variables one at a time and finish with an enquiry checklist.
Mesh size: 38, 30, 19 and 13 millimetres
A 38 mm square mesh is the most general specification: moderate open area, a comfortable walking surface, and small tools and parts do not fall through easily, which suits platforms, walkways and trench covers. It is also the mesh with the most stable supply and the widest range of accessories.
A 30 mm mesh has less open area and a more continuous bearing surface, which suits small trolley wheels and heavier tools, but it adds weight and reduces drainage and debris fall-through. The 19 mm and 13 mm meshes are fine grids, used where small parts must not fall through or where a flatter surface is required.
The smaller the mesh, the greater the weight per square metre at the same depth and the higher the price. Choose the mesh by asking what the largest falling object is and what the smallest wheel diameter is, not by appearance.
Depth and capacity are not linear
Load capacity rises with panel depth, but not in a simple linear way. A grating is a grid structure: the top and bottom flanges carry tension and compression, the vertical ribs carry shear, and a deeper panel raises both the section inertia and the rib height, so capacity usually grows faster than depth.
Reducing depth also cuts capacity quickly. The step from 25 mm to 38 mm is often not a small difference but a whole class of usable span. Replacing a thick panel with a thin one plus denser supports may save on the panel and spend more on supports and installation.
The final capacity answer comes from the manufacturer's load table, not from a guess at depth. How to read that table is covered in FRP grating load tables: uniform, concentrated and line loads, and you should confirm span and deflection limits before reading it.
The resin system sets corrosion and fire performance
Orthophthalic unsaturated polyester is the lowest-cost resin and suits general indoor and mildly corrosive environments. Isophthalic polyester resists water and moderate acids and alkalis, which suits outdoor, wastewater and marine atmospheres. Vinyl ester resists strong acids, strong alkalis and solvents, which suits chemical plant and severe coastal service.
Fire performance is a separate axis. Fire-retardant resins can be formulated to stop burning when the flame is removed, with the exact class judged under GB 8624 or ASTM E84. When fire performance is required, state the standard and the class in the enquiry; "fireproof" on its own is not a specification.
Resin also affects colour stability. Under long outdoor exposure, ordinary resins yellow and chalk; a surface veil and UV-resistant coating slow this down but cannot stop it. Projects with colour requirements should agree on a colour tolerance and a service period.
Reading the load table: span, uniform, concentrated and deflection
A load table usually lists span down the rows and load type across the columns, giving allowable values for uniform, concentrated and line loads together with a deflection limit. The first step is to confirm the span, the second to confirm the load type, and the third to check that deflection is acceptable.
Deflection often controls before strength does. Platform grating commonly uses L/200 or 10 mm as the limit, while walkways need a stiffer feel and may require less deflection. Choosing a panel that will not break but will visibly sag leaves the panel too thin.
The values in a table normally include a design safety factor, but factors and test methods differ between manufacturers. When comparing suppliers, confirm whether the header is for uniform or concentrated load, what deflection limit applies, and whether the supports are simple or fixed.
Support spacing often matters more than panel depth
On the same 38 mm grating, reducing support spacing from 1.2 m to 0.9 m can multiply the allowable load several times over. Many "not enough capacity" problems start not with a thin panel but with a beam spacing chosen by rule of thumb instead of being back-calculated from the load table.
Support spacing also has to satisfy deflection and vibration. Walkways, platforms and stairs have different comfort requirements, and maintenance platforms must allow for concentrated maintenance loads. The method is set out in FRP grating support spans: beam spacing and deflection, and you should measure the clear span before choosing the panel.
If the beams are already fixed on site, measure the actual clear span first and ask the manufacturer to select the depth for that span; do not buy panels first and then look for a way to add supports.
Slip-resistant surfaces and open area
Molded grating commonly comes with a plain, gritted or sanded surface. Plain is easiest to clean and adequate in dry areas; gritted gives better grip in wet and oily conditions; sanded gives the best slip resistance but is rough and harder to clean, which suits stair treads and areas repeatedly washed with water.
Open area affects drainage, debris fall-through and airflow, and it also changes how the surface feels underfoot. A high open area drains quickly but lets small objects fall; a low open area is flatter but traps water and dust. The combination of surface and open area should follow the actual medium and the maintenance method.
Slip testing and how to interpret it are covered in FRP grating slip resistance: gritted, sanded and wet conditions; do not rely on the word "anti-slip" in a catalogue.
Fixings, thermal expansion and expansion joints
Molded grating is held down with M-clips, stainless bolts or hold-down plates. Clips install quickly and do not damage the grating, which suits covers that must be opened often; bolts hold more firmly and suit high-vibration or high-wind areas, but every hole becomes a stress concentration.
The thermal expansion coefficient of FRP is roughly two to three times that of steel, so long runs move noticeably under large temperature swings. Leave clearance at the ends and along the long edges, and set expansion joints in large areas so the grating never bears hard against a wall or equipment foundation.
Fixings and expansion are covered in FRP grating fixings: clips, bolts and washers, and in FRP grating thermal expansion and expansion joints; follow the manufacturer's installation details.
Molded or pultruded: when molded wins
Molded grating carries load more evenly in both directions and has a regular open pattern, which suits platforms, walkways, covers and two-way bending. Pultruded grating concentrates capacity along its length, which suits long spans loaded mainly in one direction; its surface is flatter, but its transverse capacity is weak.
Projects that involve frequent cutting, drilling and on-site fitting favour molded grating because it tolerates field modification better. Projects that need very high longitudinal capacity or assembly with profiles favour pultruded grating. The structural difference is explained in molded versus pultruded FRP grating, judged by the direction of load.
Some projects mix the two: pultruded grating for main walkways, molded grating for irregular areas and covers. When mixing, remember that depth, capacity and fixing methods differ, and the joints need their own support design.
Eight items to state in an enquiry
First, mesh size. Second, panel depth. Third, resin system and fire class. Fourth, surface type. Fifth, panel size and quantity. Sixth, support span and load type. Seventh, service environment and chemical medium. Eighth, fixing method and whether edge sealing is required.
With these eight stated, a supplier can quote something comparable and avoid mismatches such as quoting a 38 mesh and delivering 25 mm depth. The molded range is shown in molded FRP grating product series, and the full category in FRP grating, where you can filter by application.
Selection is not about the thickest or most expensive panel; it is about the lowest life-cycle cost at the given span, load and environment. Control the four variables, and the rest is a matter of checking the table.
简体中文
English